Description
Maximum Controls MX116 Heavy-Duty Push-to-Open Bracket for MAX SUPER ARM 2300
The Maximum Controls MX116 Heavy-Duty Push-to-Open Bracket is a mounting accessory designed specifically for the Maximum Controls MAX SUPER ARM 2300 linear swing gate actuator. Used in push-to-open installations, this bracket provides the rear mounting connection needed to properly position and secure the actuator to a suitable gate post, wall, or reinforced mounting structure.
Constructed for demanding swing gate applications, the MX116 is intended to withstand the substantial mechanical forces generated by the heavy-duty MAX SUPER ARM 2300 during gate opening and closing.
The MAX SUPER ARM 2300 is designed for large residential and commercial vehicular swing gates, with rated gate capacities reaching 2,300 lbs under specified conditions. Proper actuator mounting is essential for maintaining correct gate geometry, smooth operation, and long-term mechanical reliability.
The MX116 is the manufacturer-specified push-to-open bracket for this actuator. Maximum Controls specifically identifies MX116 in its installation instructions when configuring the SUPER ARM 2300 for push-to-open operation.
Whether completing a new installation, converting an approved gate configuration, or replacing a damaged mounting bracket, the Maximum Controls MX116 provides the correct bracket application for compatible MAX SUPER ARM 2300 systems.
Key Features & Benefits
-
Genuine Maximum Controls Part # MX116: Manufacturer-identified push-to-open mounting bracket.
-
Designed for MAX SUPER ARM 2300: Specifically intended for the heavy-duty SUPER ARM 2300 linear actuator.
-
Push-to-Open Configuration: Supports installations where the actuator pushes the gate into its open position.
-
Heavy-Duty Mounting Application: Designed for the substantial forces associated with commercial-grade swing gate actuators.
-
Rear Actuator Mounting: Provides the required rear mounting arrangement for approved push-to-open installations.
-
Secure Structural Attachment: Intended for installation on a properly reinforced mounting plate and support structure.
-
Professional Installation Component: Suitable for new gate installations and replacement bracket applications.
-
Residential & Commercial Use: Supports compatible heavy-duty residential, estate, and commercial swing gate systems.
-
Manufacturer-Documented Compatibility: Identified in Maximum Controls' SUPER ARM installation instructions.
Technical Specifications
| Specification | Details |
|---|---|
| Manufacturer | Maximum Controls |
| Manufacturer Part Number | MX116 |
| Product Type | Push-to-Open Actuator Mounting Bracket |
| Bracket Application | Rear Actuator Mounting |
| Compatible Actuator | MAX SUPER ARM 2300 |
| Gate Type | Vehicular Swing Gate |
| Mounting Configuration | Push-to-Open |
| Advertised Heavy-Duty Thickness | 1/4 in — verify before publishing |
| Installation Method | Welded to Suitable Structural Mounting Plate |
| Primary Function | Secure and Position Actuator for Push-to-Open Operation |
| Application | Residential & Commercial Swing Gate Systems |
| Quantity | One Bracket, Unless Otherwise Specified |
Designed for MAX SUPER ARM 2300 Push-to-Open Installations
The MAX SUPER ARM 2300 supports different mounting arrangements depending on the required gate opening direction.
In a push-to-open installation, the actuator extends or retracts according to the approved geometry to push the gate into its open position.
This configuration may be necessary where property layout, gate placement, or available mounting space makes a conventional pull-to-open installation unsuitable.
The MX116 provides the specialized rear mounting arrangement required for the SUPER ARM 2300 push-to-open configuration.
Maximum Controls' installation manual specifically instructs installers to order the MX116 for this application.
Important: The MX116 is a push-to-open bracket. It is not a universal mounting bracket for all Maximum Controls swing gate actuators.
Heavy-Duty Structural Mounting
The MAX SUPER ARM 2300 generates substantial linear force during operation, making proper bracket installation critical.
Maximum Controls emphasizes that the push-to-open bracket must be mounted securely and remain level.
The manufacturer's installation illustration shows the bracket welded completely around its connection to the structural mounting plate.
A properly installed bracket helps:
-
Maintain correct actuator alignment
-
Support the mechanical loads generated during gate movement
-
Preserve the intended mounting geometry
-
Reduce unnecessary stress on actuator connections
-
Support consistent gate travel
-
Prevent movement caused by inadequate mounting
Important: The bracket must be attached to a structurally adequate mounting surface. A weak or improperly secured gate post or mounting plate can compromise the entire installation.
Maximum Controls Operator Compatibility
Compatible With:
-
Maximum Controls MAX SUPER ARM 2300 Heavy-Duty Linear Swing Gate Actuator
-
Approved MAX SUPER ARM 2300 push-to-open installations
-
Applicable single- and dual-gate systems using SUPER ARM 2300 actuators
Not Intended As a Direct Replacement For:
-
MAX SUPER ARM 1300 push-to-open bracket (MX131)
-
MAX ULTRA ARM push-to-open bracket (MX115)
-
Standard pull-to-open bracket assemblies
-
Unrelated Maximum Controls swing gate operator mounting systems
Always verify the exact actuator model and mounting configuration before ordering.
Push-to-Open vs. Pull-to-Open Mounting
Push-to-Open Installation
A push-to-open configuration uses a specialized rear mounting arrangement to position the actuator for the required gate movement.
The Maximum Controls MX116 is specifically identified for this application on the MAX SUPER ARM 2300.
Pull-to-Open Installation
Pull-to-open installations use a different rear mounting arrangement.
Maximum Controls identifies separate mounting components for these installations, and the MX116 should not be substituted without manufacturer authorization.
Choosing the correct mounting bracket is essential for achieving proper actuator travel and preventing mechanical binding.
Installation Considerations
The MX116 should be installed by qualified gate automation personnel familiar with heavy-duty linear swing gate operators.
Maximum Controls' instructions require careful attention to bracket alignment, mounting strength, and actuator geometry.
Before installation:
-
Confirm the actuator is a MAX SUPER ARM 2300.
-
Verify that the installation requires push-to-open operation.
-
Review the manufacturer's push-to-open mounting dimensions.
-
Confirm the gate post, wall, and mounting plate are structurally suitable.
-
Position the MX116 according to the installation diagram.
-
Ensure the bracket and actuator mounting arrangement remain level.
-
Secure the bracket using the manufacturer-specified welding method.
-
Confirm the actuator can move through its required travel without binding.
-
Complete the remaining actuator installation and limit-setting procedures.
-
Test gate operation and all required safety devices.
The manufacturer warns that extreme force is applied to the bracket during normal gate cycling. Proper structural mounting is therefore essential.
Ideal Applications
The Maximum Controls MX116 is suitable for:
-
MAX SUPER ARM 2300 push-to-open installations
-
Heavy-duty residential swing gates
-
Commercial vehicular swing gate entrances
-
Large estate and ranch gates
-
Gated communities
-
Industrial and commercial properties
-
Replacement of damaged SUPER ARM 2300 push-open brackets
-
Approved gate automation installation projects
Product Information & Ordering Notes
Manufacturer: Maximum Controls
Part Number: MX116
Product: Heavy-Duty Push-to-Open Mounting Bracket
Compatible Operator: MAX SUPER ARM 2300
Application: Rear Mounting for Push-to-Open Swing Gate Installations
Important Ordering Note: This product is the push-to-open mounting bracket only. The MAX SUPER ARM 2300 actuator, control box, mounting plate, anchors, and additional installation hardware are not included unless specifically stated.
Installation: Professional installation is strongly recommended. Follow Maximum Controls' current SUPER ARM 2300 installation manual for bracket positioning, welding, and mounting requirements.